Service manual epson c9100

First lift the photoconductor unit off the IDT by its orange handle, then release the end-stop on the IDT and lift it to the end of it's rails and away using the black handle. When the IDT has been replaced the Maintenance Menu is used to reset the counter and to run the colour alignment checks.

There is a bit more on changing the kit here. The printer gives a "Worn Fuser" message when the fuser unit is near the end of its service life. Printing after this message appears is not guaranteed. Epson intend that this is a dealer replaceable unit so people without technical experience should call a service engineer - its an expensive printer. Note that after a new fuser has been fitted the fuser count has to be reset.

Service technicians do this by putting the printer into a special Maintenance Mode. Power up the printer with all the direction buttons pressed to enter maintenance mode and go to the fuser reset option.

Epson sells a maintenance kit containing all three. It is probably better value that buying the parts individually if they are all life-expired and fitting them all at aonce will make better use of a service technician's time.

Standard warranty was 2 years onsite. However these machines will mainly be over 5 years old, so manufacturers warranty will have expired. Some pictures derived from Epson User and Service guides.

These technical pages do not constitute an offer for sale; just our knowledge at the time of writing. See the catalog. Sales pages on this Web site use cookies to store user information.

We also use Google Analytics to track site usage patterns. High-Speed single pass roller transfer system Multiple print sizes A4, A3 and banner printing First page out It can also take an auto duplex unit, hard disk and PostScript or PCL A printer this size is generally shared in a workgroup so the machine has an ethernet print server built in.

The ususal process may have a few disadvantages: most technicians won't be familiar with the process for consumables and spares you are almost entirely in Epson's hands. Control: Ergonomically designed control panel with an LCD status bar. EpsonNet WebManager browser for set-up and troubleshooting.

Administrators can also specify maximum numbers of colour and mono pages that can be printed on a daily basis Duty Cycle: Maximum monthly volume is stated as 80, pages. This sort of printer is moderately likely to be used for production of short run catalogues and suchlike Print Speed: A4 at 24 pages per minute.

A3 at 13ppm. First page out in Epson call their resolution enhancement "RIT" Resolution Improvement Technology and they also point out that the printer has fine control over dot size to 16 horizontal steps Paper Handling: Theres a fold-down multipurpose tray and a sheet cassette built into the printer base.

Maximum paper input is sheets - the four trays and the multifunction tray. Paper weight is 60 to gsm Tray 1: Multipurpose tray with a capacity of sheets. Width Optional tray with a capacity of sheets.

You can unsubscribe at any time with a click on the link provided in every Epson newsletter. If you would like to register as an Epson partner, please click here. Not yet an Epson partner? For more information and for registration, please click here.

Find a repair centre close. Sorry, this product is no longer available. Please see below for continued support. Find a repair centre. Epson AcuLaser C Tech Specs Product features and specifications are subject to change without prior notice. Expand All. Printing Volume. Paper Formats. A4 Product dimensions. Product weight. The printer should probably be off before an IDT installed.

The service manual leaves it open to work with power on but turning off seems a sensible precaution. The IDT has a handle to withdraw it from the machine. There is a latch inside the handle and with that pressed the handle can be turned and the unit pulls outwards. The unit should reach an end-stop. With the IDT at the end stop the Photoconductor unit lifts out of it using the orange handle. Observe how the photoconductor is hooked onto the IDT.

The rollers of the photoconductor must not be touched, and should not be exposed to bright light. Put the photoconductor unit on a level, dust free surface and limit it's exposure to light to low levels for a short time. The IDT is held by a cream-white stopper. Holding the black handle of the IDT release the stopper and lift the unit away. Take care, it is quite heavy.

A new unit can be lifted into place on the rails that held the old one. The stopper needs to be in it's disengage position to slide in. The Photoconductor unit mounts back in the new IDT in the same way the old one was held. The printer should be turned on and allowed to warm up for some time. Maintenance mode is activated by holding down Back, UP Down and enter buttons on the operator panel at power on.